S1 | Motorized camera slider with panning motor
Check out our motorized slider S2
- The model S1 is a motorized camera slider and a panning motor capable of fluid movements with no vibrations thanks to its bearings. you can use it instead a dolly. The best value-for-money slider.
- Dslr slider includes 100cm and 50 cm tubes.
- Made from aluminium. Light and robust, 1,5kg.
- Compatible with any camera or dslr. Can carry up to 5kg.
- It can be placed upside-down and vertically. A tripod or monopod can be attached to each end or, if you prefer, you can use the anti-slip feet that can be adjusting according to the terrain.
- Extend it by adding 20mm-diameter tubes, available in any hardware store.
-
S1-Motor 149€
Motor para el S1-Slider
- Create a motorized camera slider
- Stepper motor, powerful and very precise
- Very silent — perfectly suitable for recording audio in an interview
- Capable of moving cameras of up to 15kg horizontally and up to 2kg vertically
- Fast and very precise — ideal for suitable for video and timelapses
-
S1-Slider
199€149€
- The controller is capable of controlling a slider (S1-Slider + S1-Motor) and a Pan Motor (S1-Pan)
- Modes: FreeMove, Video (smooth videos), Timelapse (includes a shutter, shoot-move-shoot), long exposure, stop-motion, Panorama, and Turntable.
- Control your camera or dslr like a motorized dolly
- Designed and manufactured in Europe
Check out our motorized slider S2
How can I control the motorized camera dolly and panning motor?
Freemove mode:
Turn the controller to set a target speed, and the engine will gradually increase speed up to the target.
Video mode:
- Turn the controller to move the slider and press to select the initial frame or position.
- Turn the controller to select the final position.
- Select the duration in seconds.
- Loop? (restarts after one cycle without interruption)
- Press Start. If loop mode is not activated, it will stop at the end will ask if you want to repeat the take.
Timelapse mode:
- Turn the controller to move the slider and press to select the initial frame or position.
- Turn the controller to select the final position.
- Select the number of photos and the time interval between each one, and the system will automatically calculate the total recording time and the duration of the final result.
- Loop? This is ideal if we want a timelapse that will start and return to the initial position when finished.
- Connect the shutter cable and press Start.
Long Exposure mode:
- Select the minutes and seconds for the duration of the shoot.
- Connect the self-timer cable and press Start.
Stop-motion mode:
- Turn the controller to move the slider and press to select the initial frame or position.
- Turn the controller to select the final position.
- Select the number of photos and press Start.
- Once you shoot a photo, the engine will advance automatically. If you make a mistake, don’t worry: just go back to the start and the engine will return.
Where can I buy the motorized dslr slider harrope?
Check out our motorized slider S2
You can buy the motorized camera slider in parts:
S1-Slider includes:
- Slider with two separators with anti-slip rubber feet
- 100cm tubes
- 50cm tubes
- Large screw (3/8”)
- 2x Small screw (1/4”)
S1-Motor includes:
- Engine
- 100cm belt
- 50cm belt
- Screws for initial installation
- 1m-long RJ45 cable to connect the engine to the controller
S1-Controller includes:
- S1-Controller
- Power source
S1-Pan includes:
- Motor Pan
- Adaptador rosca pequeña a grande
- Cable RJ45 de 1 m para conectar el motor al controlador
What batteries can I use?
The S1-Controller comes with just one power source. if you need a battery, you’ll need to purchase one separately
What cable can I use to shoot with my camera?
Attached you’ll find the shooter cable to connect your camera and the controller.
How to install the S1-Motor with S1-Slider :
Installation is very simple — it should only take about 5 minutes. Once installed, you can easily return to Manual Mode by removing two nuts by hand.
Technical specifications:
- Weight: 1.5kg
- Size: 100cm x 20cm x 8cm
- Movement distance: 88cm
- Supported weight:
- 5kg with the 100cm aluminium tubes; 30kg with steel tubes
- 30kg with 50cm aluminium tubes





